UPM HTM621 Spezifikationen Seite 1

Model No.HTM621Programmable ThermostatFor Electric Baseboard HeatersHigh VOLTAGE120 V/ 240 V AC, 60 HzRef: HTM621 UPM BRAND

8If you have successfully installed the thermostat, but the LCD screen does not display or the display seems abnormal, press the RESET button. (The re

9Programming

LCD Display10P2P3P4P1 MOTUWETHFRSA SUPMUSAGESETTIME / USAGEPROGRAM PERIODSSET TEMPERATURECURRENT TEMPERATUREHEAT “ON” ICONWEEKDAYSPOWER OUTPUT LEVEL

Buttons11USAGEDisplays the total time spent heating per day or week.COPYCopies program settings from one weekday to another.HOLDSuspends automatic pro

SET CLOCK12P1 TUPMSETTIMEWEEKDAYSSet Clock / Weekday Press SET to enter the clock-setting mode.(SET will display and the clock symbol/time flashe

13Select °C or °F (Celsius or Fahrenheit) Press SET for 3 seconds to enter the option setting mode. Press SET 3 times (until the temperature and °F

Program Heating This is typically the morning hours, when you may prefer to wake up

The program periods (P1,P2, P3, P4) allow you to set the temperature settings and start times throughout the day. These are examples of possible tempe

First select the day you wish to program, then select the start times and temperature settings for all four program periods. Scroll through the daily

This thermostat can copy program period settings from one day to another using the COPY function. All four period settings (P1, P2, P3,P4) will be cop

Features:Ideal for electri c baseboards, fan assisted (conve ctors) and radiant ceil ing heating7-day program ming with 4 program s per dayCopy on

If you have difficulty programming your thermostat, you may wish to restore the factory settings and begin again.RESTORE PROGRAMS AND OPTIONSPress SET

19This function will allow you to change the temperature setting until the start time of next program period.Press the UP or DOWN button to manually a

20OPERATIONCurrent Temperature DisplayThe current (room) temperature is displayed on the LCD screen.Power BarThis thermostat is equipped with a propor

21The thermostat tracks the system "ON" time; the total time the heating equipment is running.Press the USAGE button once to view USAGE TODA

22OPTION 1 - 12- or 24-Hour Clock Format Press and hold SET for 3 seconds to enter the Option Setting mode.The first option is 12- or 24-hour clock f

23OPTION 4 - °C or °F DisplayPress SET again to select Celsius or Fahrenheit scale (the current temperature will flash)Press UP or DOWN to toggle betw

24Heat Cycle RateCycle rate determines the heating on/off time cycles and the level of proportional power required to operate the heater. (To have the

25Setting the HIGH-LIMIT FUNCTIONTo enable this feature and set a maximum temperature, first press the "UP" or "DOWN" key until th

SPECIFICATIONSRating: 120 V/240 V AC, 60 HzMax. load: 16.6 A 4000 W @ 240 V or 2000 W @ 120 VMin. load:

PROBLEM SOLUTIONThe heating system will not activate. Heating system seems to cycle too often.- Check the thermostat LCD display to see if there has b

Table of ContentsInstallation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28Limited 5-year Repair WarrantyThis product carries a five (5) year warranty against defects in workmanship and materials. This product is not guaran

Installationinstructions2

IntroductionThis thermostat is for use with high voltage systems (120 V/240 V) such as electric baseboards, radiant ceiling/floor heaters and convecto

HEATING SYSTEMSCentral Heating Furnace System(24 V) COMPATIBILITYNoCOMPATIBILITYGenerally, equipment with high-voltage control is only compatible with

Thermostat should be mounted:on the existing metal electrical box that controls your heater.Note: Ensure that the thermostat is not near heat sensitiv

6INSTALLATION THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE CANADIAN ELECTRICAL CODE, AND IN QUEBEC, BY A QUALIFIED ELECTRICIAN.The manufa

7INSTALLATION Mount the thermostat to the wall box using two screws through the mounting holes, and then replace the faceplate. (Place screws in t